A MOSFET takes the current off your trigger contacts and puts it through a transistor. The result is a crisper trigger, no burnt contacts on 11.1 V and, with an ETU, fire modes you program.
1–24 of 88 products
In stock, ships right away
AB plus plus mosfet and active break
In stock, ships right away
LEVIATHAN NGRS Optical M4 (Rear Wiring)
In stock at our supplier, delivery in 5–10 working days
ETU plus plus upgrade for G&G (with T-Deans plug)
In stock at our supplier, delivery in 5–10 working days
V2 Lightning ETU Unit – Wiring to the Stock
In stock at our supplier, delivery in 5–10 working days
MOSFET
In stock at our supplier, delivery in 5–10 working days
Scylla V2 ETU Unit - Wiring to stock
In stock at our supplier, delivery in 5–10 working days
Fixed Stock Wire Set For AEG
In stock at our supplier, delivery in 5–10 working days
M4 Handguard Wire Set
In stock at our supplier, delivery in 5–10 working days
Wire set M4, CAR - 15, XM177 (Handguard)
In stock at our supplier, delivery in 5–10 working days
Wire Set G36
In stock at our supplier, delivery in 5–10 working days
Wire set AK (Folding stock)
In stock at our supplier, delivery in 5–10 working days
Wire set MP5(Handguard use)
In stock at our supplier, delivery in 5–10 working days
Wire set MP5(Fixed stock use)
In stock at our supplier, delivery in 5–10 working days
MOSFET II
In stock at our supplier, delivery in 5–10 working days
Swith set for gearbox v.3
In stock at our supplier, delivery in 5–10 working days
Swith set for gearbox v.2
In stock at our supplier, delivery in 5–10 working days
ECU Processor Unit with Wiring for CZ Scorpion EVO 3
In stock at our supplier, delivery in 5–10 working days
Large Capacity Switch Assembly ( Ver.3 / Front )
In stock at our supplier, delivery in 5–10 working days
Large Capacity Switch Assembly ( Ver.2 / Rear )
In stock at our supplier, delivery in 5–10 working days
Large Capacity Switch Assembly ( Ver.2 / Front )
Out of stock, also at our supplier
HPA Trigger Board ETU for V3 GearboxIn a stock AEG the trigger contacts switch the full motor current, which arcs and pits them, and an 11.1 V LiPo makes it worse within a few games. A MOSFET lets the trigger send a small signal while the transistor carries the load, so the contacts last and the motor gets the full voltage with less loss. Active braking stops the motor at the end of each cycle, which prevents overspin and double shots on semi-auto. A simple MOSFET is the cheapest reliability upgrade for any gun running a LiPo battery.
An ETU replaces the trigger contacts and often the cut-off lever with an optical or micro-switch board inside the gearbox shell. It adds programmable modes: burst, pre-cocking for an instant first shot, adjustable trigger sensitivity, rate-of-fire control and low-voltage protection for the battery. Some units read the cycle with sensors and detect jams. ETUs are designed per gearbox version, V2 and V3 mostly, and per shell generation, so use the gearbox version and compatibility filters and read the fit notes carefully. Brushless motors need an ETU that supports them.
Low-resistance silver-plated wire, Deans or XT60 connectors and a clean solder joint matter as much as the board. Wiring harnesses for front and rear-wired guns are listed under the type filter. Electronics are unrestricted parts, and a build usually goes with new internals from gearbox and internals.
Airsoft Bazaar B.V. · Frankrijkstraat 4, 5171 PR Kaatsheuvel · Chamber of Commerce (KvK) no. 99363534 · VAT no. NL868954482B01
© Airsoft Bazaar - All Rights Reserved 2026